We have collected all the error codes of Electrolux washing machine with a detailed description of the causes of malfunctions, diagnostics and repair. For convenience, arranged in a convenient and understandable table below.
The models with the display show the alphanumeric combination on your display, find it in the table and find out the reason for the error.
Models without a display do not execute the specified program and according to the lit or flashing lights placed on the control panel, you can find out the problem.
| Error code | Description | Causes and solution |
|---|---|---|
| E11 | Water was not drawn to the required level for a certain time. | Check the inlet valve, winding (3.75 kΩ resistance) and its triac on the controller. Also check for clogging and normal pressure in the water supply. |
| E13 | Water leaking into the sump detected. | Inspect the machine for leaks. |
| E21 | Waste water was not drained in the allotted time. | Check the drainage system for blockage, pump, filter, and pump winding resistance (approximately 170 ohms). |
| E23 | The control triac of the drain pump is out of order. | Need diagnostics triac and controller. If broken, install a new element. |
| E24 | Open circuit in the control circuit of the drain pump triac. | Diagnostics of the health of circuit elements. |
| E31 | The pressure sensor is out of order. | Replace sensor or wiring. |
| E32 | The pressure meter is not calibrated. | Calibrate the meter. Open the water tap, check or replace the filler valve, clean the filter. If broken, replace the pressure sensor itself. |
| E33 | Open connection between water level sensors. | 1. The sensors are out of order. 2. The tubes are clogged. 3. High voltage in the power supply. 4. Leak on the heater. |
| E34 | The pressure switch and anti-boiling level 2 lost contact. | Install a new pressure sensor, tube, or pressure switch itself. |
| E35 | Water in the tank exceeds the permissible level. | During filling, there was an overflow of water in the tank. Check pressure switch, replace if broken. |
| E36 | The heater protection sensor has broken. | Need diagnostics and possibly replace the sensor. |
| E37 | The first water level sensor is broken. | Diagnostics and sensor replacement. |
| E38 | Clogged pressure switch tube. | Inspect the pressure switch tube for clogging. |
| E39 | Overflow level meter defective. | Check and replace the meter. |
| E3A | The relay of the heating element is out of order. | Check item and electronic unit. Replace if broken. |
| E41 | The hatch door is not tightly closed. | Close the hatch again. |
| E42 | The hatch door is not locked. | Make sure the lock is in good condition. |
| E43 | The triac of the hatch lock broke. | Diagnostics of the control triac responsible for locking the door. |
| E44 | The sunroof cover sensor is out of order. | Check and replace. |
| E45 | An open in the control circuit of the triac lock of the boot shaft hatch. | Diagnostics of circuit elements. |
| E51 | A short circuit has occurred in the control triac of the motor. | Check and in case of failure, replace the motor control triac. |
| E52 | The electronic controller does not receive a signal from the motor tachogenerator. | Correct the tachogenerator sensor, the fixing washer may have disconnected from the tachogenerator body. |
| E53 | Failure in the control circuit of the motor triac. | Check the connection between the elements. |
| E54 | Sticking in the reverse motor relay. | Check, replace the reverse relay. |
| E55 | The engine circuit has failed. | Replace wiring and motor. |
| E56 | Exceeding the permissible current value, more than 15A. | Install a new electronic unit, wiring, engine. |
| E58 | Exceeding the maximum permissible value of the phase current of the motor, above 4.5A. | The electronic unit, wiring and engine need to be replaced. |
| E59 | The tachometry signal is not transmitted after changing the rotation speed. | Check and replace the engine, tachometer generator, electronic unit, wiring. |
| E5A | Overheating of the cooling radiator, above 88 ° C. | Install a new electronic unit. |
| E5B | Low voltage in the DC bus, below 175V. | Diagnostics and replacement of the electronic unit and wiring are required. |
| E5C | High voltage in the DC bus, above 430V. | Assess the condition of the electronic unit; if broken, replace. |
| E5D | FCV does not receive or send signals for more than 2 seconds | The problem is the operation of the electronic unit. |
| E5E | The FCV control board and main circuit board have lost communication. | Change the electronic unit to a working one. |
| E5F | The FCV control card sends a request for configuration parameters without interruption. | Make sure the electronic unit is intact and the wiring is intact. Replace if necessary. |
| E61 | The water temperature does not reach the time required for this task. | The code is not read in the normal mode of operation of the machine. You need to enable the diagnostic mode. Inspect the heater with a tester, the resistance at room temperature should be approximately 30 ohms. |
| E62 | Overheating of water after reaching the specified time. | The temperature meter failed. Use a tester to measure resistance, 5.7 - 6.3 kOhm at room temperature. Inspect the case, maybe the heater breaks through. |
| E66 | Relay tubular heater out of order. | Replacing the heater relay and control circuit. |
| E68 | Excessive leakage current in the machine. | Install a working heating element. |
| E71 | Excessive temperature sensor resistance. | Sensor short circuit or open circuit. Checking items. |
| E74 | The temperature meter (NTC) is not correctly located in the tank. | Correctly position the sensor. |
| E82 | Wrong selector position. | Check the electronic unit, selector, wiring for functionality. |
| E83 | Data from the selector is not read. | The error is displayed only in diagnostic mode. Failure occurs due to improper configuration or breakdown of the electronic unit. |
| E84 | Recirculation pump not recognized. | The electronic unit needs to be replaced. |
| E85 | Thyristor or recirculation pump out of order. | Diagnose and change these elements. |
| E91 | There is a loss of communication between the main unit and the user interface. | The electronic unit must be replaced with a new one. |
| E92 | There is a mismatch between the main unit and the user interface. | Install a working electronic unit. |
| E93 | Error configuring the washing machine. | Enter the correct configuration code to correct. |
| E94 | Incorrect machine or program configuration. | Overwrite the volatile memory of the controller. If it does not help, replace the board. |
| E95 | There is no connection between the processor and the memory that are located on the electronic controller. | Need to check the circuits between all of these elements and EEPROM. |
| E96 | Incorrect configuration of the electronic controller and external elements. | Make sure that the controller and its external elements are configured correctly. |
| E97 | Program selector and electronic controller software malfunctioning. | Enter the correct configuration for your Electrolux washing machine. Possible replacement of the main unit. |
| E98 | Incorrect operation between the engine control unit and the electronics. | The problem is in the electronics or wiring. |
| E99 | Not the factory connection of the sound block and electronics. | Replacing wiring or sound unit. |
| E9A | The speaker and electronics software is faulty. | The electronic unit needs to be replaced. |
| EA1 | The DSP system has failed. | Check DSP, main unit, wiring, drive belt. Replace the broken items. |
| EA2 | DSP not recognized. | Install a working main unit. |
| EA3 | DSP does not lock motor pulley. | Checking and replacing DSP, main unit, wiring, drive belt. |
| EA4 | Damage to the DSP. | Install a new DSP, main unit, wiring. |
| EA5 | Thyristor DSP is out of order. | Install a working main unit. |
| EA6 | For the first 30 seconds of operation, there is no drum rotation signal. | The drum leaf may not be closed. Also check the drive belt and DSP. |
| EB1 | The frequency of the power supply does not meet the permissible frequency. | Check the power settings. |
| EB2 | High voltage power supply. | Make sure there is no high voltage on the network. |
| EB3 | Low voltage power. | Check your network settings. |
| EBE | The protective relay is defective. | Need diagnostics of the electronic unit. |
| EBF | The protective circuit is not recognized. | Failure of the electronic unit. |
| EC1 | Jam valve lock. | Check the performance of the filler valve, electronics, wiring. |
| EC2 | The water transparency sensor has failed. | Replace the item. |
| EF1 | Waste water does not merge for a certain time. | Inspect and clean the drain system, drain hose, filter, pump. |
| EF2 | Increased foaming during discharge. | Clean the drain system. Reduce the dosage of washing powder. |
| EF3 | Activated Aqua Control system, water leakage. | Inspect cable, drain pump. |
| EF4 | With active filling valves, there is no signal from the flow sensor. | Open the water tap. Check the pressure in the water supply system. |
| EF5 | The imbalance is greater than permissible. | Redistribute the laundry in the drum or separate more than one wash. |
| EH1 | Exit the permissible limits of the supply voltage frequency. | Due to interference in the power supply or inappropriate source. There may be problems in the electronics. |
| EH2 | Excessive supply voltage | Unsuitable power source. Check the electronic unit. |
| EH3 | Low voltage power. | There may be interference with the power supply or a problem in the electronics. |
| EHE | The protective relay is defective. | Diagnostics of the electronic unit. |
| EHF | The protective circuit is not recognized. | Checking and replacing the electronic unit. |