Error codes washing machine Miele

We have collected all the error codes of Miele washing machine with a detailed description of the causes of malfunctions, diagnostics and repair. For convenience, arranged in a convenient and understandable table below.

The models with the display show the alphanumeric combination on your display, find it in the table and find out the reason for the error.

Models without a display do not execute the specified program and according to the lit or flashing lights placed on the control panel, you can find out the problem.

Miele washing machine errors, decoding

Error code	Description	Causes and solution
F01	The drying temperature sensor has failed.	Short circuit in sensor or connection circuit.
F02	No communication with temperature meter (NTC).	Inspect and repair open wire connections.
F03	Sensor Problem (NTC)	Replace the element damaged by a short circuit.
F04	Drying temperature meter defective.	NTC or sensor wiring open. Check connectors, wiring. If broken, replace with a new element.
F10	Water does not enter the machine.	Perhaps the valve is closed, blockage in the supply system, filter, valve.
F11	For a certain time, the waste water did not merge.	There may be a blockage in the drainage system, filter or pump breakdown.
F15	Instead of cold water, the tank is filled with hot.	Incorrect machine connection. Turn off the hot water faucet, check that the supply system is connected correctly.
F16	Increased foam formation.	Too much detergent or poorly drained waste water. Try using less powder or replace it with another.
F19	The water flow meter is out of order.	Very slow or lack of rotation of the sensor due to blockage.
F20	Miele washing machine does not heat water.	Check the operation of the temperature sensor and the tubular heater. Replace the defective item.
F29	The tubular heater in the dryer is broken.	The drying heater burns out; replace with a working one.
F34	The boot shaft hatch does not close.	The electronic interlock or door parts are broken. Replacement with new elements is needed.
F35	The hatch door is locked.	There may be a blockage / breakage of the lock or lock system, a malfunction of the control board.
F39	The control module has failed.	Diagnostics and replacement of the electronic control module are needed.
F41	Non-volatile memory failure.	The element gives incorrect values; install a new non-volatile memory in the control module.
F43	No firmware found.	Module firmware memory failure or model type not programmed.
F45	Electronics failed.	RAM memory gives incorrect data. Put a new item.
F46	Display malfunction.	Broken contacts or incorrect display connection.
F47	Interface malfunctions	Check the functionality of the option module relay.
F49	Interface error.	Need diagnostics and replacement of failed parts.
F50	Faulty control module.	It needs repair or a complete replacement.
F51	The pressure sensor is out of order.	It is necessary to check whether the contact is open. If everything is in order, then replace the pressure switch with a working one.
F53	Damage to the drum speed meter.	Need a replacement tachogenerator.
F55	Performance monitoring sensor is broken.	Install a working sensor.
F56	Engine tachogenerator defective.	Power loss, spin speed below 400 rpm. Check sensor winding.
F62	Problem with program selector.	It is necessary to replace the selector with a new one.
F63	The water control unit has failed.	Check, repair or replace the unit.
F64	The water trajectory control system is out of order.	Need diagnostics and replacement of broken parts.
F65	There is no drum light.	Check the contacts of the backlight system.
F81	The drying unit broke.	Diagnose or completely replace the unit.
F83	Exceeding the permissible temperature or overheating of the drying.	Check if the thermistor is working. In case of malfunction, replace with a working one.
F92	Possible occurrence of fungus or mold.	Inspect the machine, make sure that the operating conditions are correct.
F93	The relay of the optional control module is broken.	Repair or replace.
F96	Alternative water supply is not possible.	Check all elements of alternative water supply and repair / replace them.
F100	There is no connection with IK6.	Disruption or interruption of communication with IK6. Repair and replacement of broken parts.