We have collected all the error codes of Siemens washing machine with a detailed description of the causes of malfunctions, diagnostics and repair. For convenience, arranged in a convenient and understandable table below.
The models with the display show the alphanumeric combination on your display, find it in the table and find out the reason for the error.
Models without a display do not execute the specified program and according to the lit or flashing lights placed on the control panel, you can find out the problem.
| Error code | Description | Reasons and Solution |
|---|---|---|
| F01 | The sunroof is not locked. | Make sure that the door is tightly closed and locked, that the lock and the locking mechanism are in good working order. Perhaps a foreign object interferes with the closing of the door. |
| F02 | No water is supplied to the machine. | Perhaps the cold water supply tap is closed, low pressure in the water supply system, clogging of one of the elements of the supply system path. |
| F03 | Waste water does not drain. | Siemens washing machine does not drain water in a certain time (10 minutes). Check the drain system, filters, hose, drain pump, nozzles. Possible clogging of one, several elements or their malfunction. |
| F04 | Water leak detected. | Inspect the machine and find the source of leakage, leakage of elements and connections. |
| F16 | The hatch of the machine is not completely closed. The set wash program is not running. | Close the door again, check the operation of the lock. Run the program again. |
| F17 | For a certain time, water did not accumulate. | Closed feed tap, clogged filter, hose. Perhaps the valve is locked in the closed position or something prevents full opening. |
| F18 | For the allotted time for the task, the machine did not drain the water. | Clogged filter, drain pump, hoses and nozzles. Must be inspected and cleaned. Perhaps the pump, pressure switch, water controller are faulty. |
| F19 | In the right time, the water did not heat up. | Check the mains voltage, the health of the tubular heater and its circuits. |
| F20 | Heating occurs without a command. | Check the operation of the temperature sensor, electric heater relay. |
| F21 | The control system is out of order. Incorrect operation of the drive motor and lack of rotation of the drum. | Diagnose the control system, triacs, tachogenerator, drive motor and reverse relay. |
| F22 | Failure of the temperature meter (NTC). | A short circuit or damage to the meter, its circuits has occurred. |
| F23 | The Aqua Stop system is activated. | Inspect the system for possible water leakage and open circuit connections. See if the pan is full. |
| F25 | Turbidity meter is out of order. | Remove lime from the measuring device. The pressure switch may be defective or the drain system may be clogged. |
| F26 | The pressure sensor (pressure switch) has failed. (Critical error) | To reset it, press the On / Off key. Replace the pressure sensor with a working one. Inspect the connection chains for an open. |
| F27 | There is a problem with the pressure sensor setting. | Sensor setting not updated. Check pressure switch and wiring. |
| F28 | Flow sensors are out of order or showing incorrect values. | It is necessary to check the operation of the flow sensor and its wiring. |
| F29 | The flow sensor does not detect the passage of water. | Make sure that the feed tap is open, there is no blockage in the feed system and good pressure in the water supply. There may be a fault in the wiring or the sensor itself. |
| F31 | Water level exceeds maximum permissible. | Check pump, water supply valve, solenoid valve, pressure sensor, drain hose, waste water removal system. |
| F34 | The door lock is not blocked. | Reset the error by pressing the On / Off button. Make sure the lock, locking mechanism, gaskets, mechanical parts are working. |
| F36 | The lock system is out of order. | To clear a critical error, press the On / Off button. Check control module, wiring and lock system. |
| F37 | The temperature sensor is broken. The washing program will continue without heating. | Check the NTC sensor, there may be a break in its wiring. If broken, install a new one. |
| F38 | NTC sensor defective due to short circuit. | Diagnose the sensor and wiring. Replace if damaged. |
| F40 | Sync failed. | High or low voltage in the power supply, out of range. |
| F42 | Engine rpm too high. | To reset the error, run the test program. Check control module. |
| F43 | Engine failure. No rotation. | By running the test program, the error will be reset. It is necessary to check the tachogenerator, module, wiring, engine or drum lock, triac. |
| F44 | There is no rotation in the opposite direction. | Run the test program to reset. In this case, the module, triac and reverse relay are checked. |
| F59 | 3D Sensor failed or malfunctioning. In this case, the speed decreases. | Check 3D sensor, wiring, magnet position, module. Possible wiring breakage, breakdown of the power module. |
| F60 | The flow meter indicates a value that is too high or low. | Diagnostics of the flow meter, filter and filler valve. Check wiring and sensor itself. |
| F61 | Hatch door signal for malfunction. | The On / Off key will clear the error. It is necessary to check the operability of the door lock mechanism, the wiring and the locking mechanism. |
| F63 | Functional protection failed. | The problem is with the power module, processor, or software failure. Press On / Off to clear the error. |
| F67 | Incorrect card encoding between power and control modules. | Re-encode the card. If this does not help, replace the card with a working one. |
| E02 | The electric motor is out of order. | Inspect the brushes, measure the resistance of the motor, clean the contacts of the connections. Verify that the engine module and main module are operational. |
| E67 | Incorrect module encoding. | You must upgrade or reinstall the firmware. Call the wizard or program the module yourself. If this does not help, you need to replace the module with a new one. |